Construction Boundary Monitoring: Protecting Workforces & Communities

By: Tim Turney, Contributor

Construction dust can compromise air quality; environmental noise pollution can be harmful to workers and local residents; and excessive vibration can have damaging consequences. Site management has a duty of care to protect against potentially dangerous conditions. However, this can be challenging to manage without reliable data streams and instrumentation that gathers environmental information. Consequently, more companies are turning to boundary monitoring technology to measure the risks and ensure they adhere to environmental limits and guidelines.

Site boundary or “fence line” monitoring is used widely on construction sites and other high-risk locations, including demolition projects, mines and quarries, and environmental remediation sites. Boundary monitoring units are set up on the exterior perimeter of the worksite to monitor for potential hazards that might cause compliance issues for the site or present a health risk to site neighbors. It is an essential part of the safety and risk management ecosystem of these sites, and it helps control and mitigate potential environmental, health and reputational risks.

Identifying Potential Hazards

Hazards that are typically monitored for include excess levels of dust, noise, vibration and, in some cases, volatile organic compounds (VOCs). VOCs include a variety of chemicals, some of which may have short- and long-term adverse health effects. If these are present on a site or work their way into soil or groundwater, they can present a hazard to future development or remediation of a worksite or property.

Achieving Compliance

Combined boundary monitoring solutions, such as the Casella Guardian 2, can continually measure conditions on or around a worksite and provide customizable, automated reports—thus allowing managers to check data streams across multiple units and multiple sites remotely. (photo courtesy Casella Solutions)

There are stringent legal and environmental controls surrounding levels of noise, dust and vibration that construction projects cannot exceed. For example, in the U.S., the Noise Control Act of 1972 establishes a national policy to promote an environment for all Americans free from noise that jeopardizes their health and welfare. While primary responsibility for noise control rests with State and local governments, the act ensures that Federal action deals with major noise sources in commerce, control of which requires national uniformity of treatment.

In New York, a city under constant renovation and construction, the Noise Code mandates that all construction must be conducted in accordance with noise mitigation plans that address the specific location, type of work and timing of a project. Sites must be able to provide evidence of compliance and maintain their reputations, and local communities must be considered. For example, when construction activity is planned near locations such as schools, hospitals and houses of worship, the party responsible for construction is expected to design their noise mitigation plan to be sensitive to its neighbors. If noise complaints are received, an inspector will ensure the contractor has posted the plan and that it is being followed. To achieve compliance, site monitoring must be recorded and reported upon, and action taken if limits are exceeded.

If complaints arise, responsible companies using boundary monitoring have proof points to show they have been diligent with their monitoring in operations and abiding by operational requirements. Data evidence from a boundary monitoring system is also helpful if a worksite is accused of issues caused by another operation—allowing site managers to respond rapidly, minimizing reputational damage.

Ensuring Accuracy

Understanding how to mount any environmental monitor is essential to obtain accurate results. For example, noise monitors should not be mounted against flat surfaces, because this will result in noise levels being overestimated. Any microphone should be above hoardings, with a clear line of sight to the nearest receptor. Inlets for any real-time dust measurements should also be clear of obstacles and be mounted away from buildings, ideally between 1.5-4 meters above the ground. When measuring vibration, the sensor should be mounted to a concrete plinth firmly attached to the ground to ensure accurate measurements.

Taking Advantage of Combined Solutions

A variety of different monitoring solutions can be employed and combined to give a full picture of site emissions and risks. Increasingly, project managers and occupational hygienists are turning to combined solutions that continually measure conditions on or around a worksite and provide customizable, automated reports—thus allowing managers to check data streams across multiple units and multiple sites remotely.

Site managers are busy people, so less frequent manual maintenance of environmental monitors is key. Having a single unit that can measure parameters such as noise, dust and vibration means only one unit to install—and one set of software with which to interact and learn—making the process easier and saving time. Once units are installed at a site boundary, they need very little interaction; “set it and forget it,” as the phrase goes. They enact monitoring 24/7 without input, running either from mains, battery or even solar-powered configurations.

Site boundary or “fence line” monitoring is an essential part of the safety and risk management ecosystem of various construction sites; it helps control and mitigate potential environmental, health and reputational risks. (photo courtesy Adobe Stock Images)

Preventing Issues with Surrounding Residents

Users can receive automatically generated, customized reports to a set schedule or when specific emissions limits are reached, preventing issues with surrounding residents and subsequent complaints to authorities. Limits can be used to trigger preventative measures, such as dust suppression.

Managers only need to check a single unit or combined data report, which is a more efficient method than checking multiple monitors and data sources. Alerts can be sent instantly via text, allowing sites to monitor levels around-the-clock and react quickly to reduce levels of dust or noise that exceed set limits and mitigate potential negative outcomes. This gives site managers a reliable data source that can be accessed any time.

Daily, weekly or monthly reports can be sent directly to an email inbox in graphical or tablature format and can even be supplied directly to local authority or environmental organizations—getting ahead of potential site visits from inspectors. If possible, baseline conditions should be established by testing before the start of operations and continued throughout the operation to observe site emissions and ensure compliance with planning conditions. Having access to real-time, near-reference data can help save site managers time, ensure environmental incidents are prevented and keep more people safe.

About the Author:

Tim Turney is Global Marketing Manager at Casella and graduated as an engineer from Queen Mary and Westfield in London. Since starting at Casella in 1998, Tim has been involved in the acoustics and air sampling industry, specializing in measurement and instrumentation technologies. Casella is dedicated to reducing occupational health and environmental risks and supporting businesses in solving their monitoring and analysis needs. For more information about Casella’s noise monitoring solutions visit, https://www.casellasolutions.com.

Share on Socials!

Related Articles

Related Articles

Portable Gas Detection Equipment: Do You Have the Right Tools for the Job?

photo courtesy Industrial Scientific Corporation By: Dante Moore, Contributor On the job, do you know that your gas detectors will protect you? Do you have the ...
Read More

Growth of Nitrile Glove Market Means Buyers Need To Beware

Matthew Piortrowski and Brian Moseley, Contributors Common sense goes a long way in making purchasing decisions. Looking into a company’s background and credentials is important when ...
Read More

Listen Up! From the NHCA Experts…

Safe-in-Sound Award: Real-World Successes in Hearing Loss Prevention By: Thais C. Morata, NIOSH Senior Research Audiologist and NHCA Expert Figure 1: Team that conducted a site ...
Read More

Follow IHW!

Subscribe!

Sign up to receive our industry publications for FREE!

Industrial Hygiene

Construction Safety